Search results

The purpose of this paper is to study the microstructure and properties of Sn-3.5Ag and Sn-3.5Ag-0.5Sb lead-free solder alloys with and without a rotating magnetic field (RMF).

Optical microscopy, scanning electron microscopy and X-ray diffraction were used to analyze the effect of an RMF on the microstructure of the solders. Differential scanning calorimetry was used to study the influence of the RMF on the thermal characteristics of the solders. The mechanical properties of the alloys were determined by tensile measurements at different strain rates.

The ß-Sn grains and intermetallic compounds for the Sn-3.5Ag and Sn-3.5Ag-0.5Sb lead-free solder alloys were refined under an RMF, and the morphology of the ß-Sn grains changed from dendritic to equiaxed. The pasty range was significantly reduced under an RMF. The ultimate tensile strength (UTS) of Sn-3.5Ag improved under the RMF, whereas the UTS of Sn-3.5Ag-0.5Sb decreased slightly. The addition of Sb to the Sn-3.5Ag alloy significantly enhanced the UTS and elongation (El.%) of the samples. The UTS of the solder increased with increasing strain rate.

The results revealed that the application of RMF in the molten alloy had a significant effect on its microstructure and mechanical properties. The thermal characteristics of the Sn-3.5Ag and Sn-3.5Ag-0.5Sb solder alloys were improved under the RMF. This research is expected to fill a knowledge gap regarding the behaviour of Sn-Ag solder alloys under RMF.

The purpose of this paper is to study the drop reliability of ball-grid array (BGA) solder joints affected by thermal cycling.

The drop test was made with the two kinds of chip samples with the thermal cycling or not. Then, the dyeing process was taken by these samples. Finally, through observing the metallographic analysis results, the conclusions could be found.

It is observed that the solder joint cracks which were only subjected to drop loads without thermal cycling appeared near the BGA package pads. The solder joint cracks which were subjected to drop loads with thermal cycling appear near the printed circuit board pads.

This paper obtains the solder joint cracks picture with drop test under the thermal cycling.

The purpose of this study is to investigate the effects of Ce and Sb doping on the microstructure and thermal mechanical properties of Sn-1.0Ag-0.5Cu lead-free solder. The effects of 0.5%Sb and 0.07%Ce doping on microstructure, thermal properties and mechanical properties of Sn-1.0Ag-0.5Cu lead-free solder were investigated.

According to the mass ratio, the solder alloys were prepared from tin ingot, antimony ingot, silver ingot and copper ingot with purity of 99.99% at 400°C. X-ray diffractometer was adopted for phase analysis of the alloys. Optical microscopy, scanning electron microscopy and energy dispersive spectrometer were used to study the effect of the Sb and Ce doping on the microstructure of the solder. Then, the thermal characteristics of alloys were characterized by a differential scanning calorimeter (DSC). Finally, the ultimate tensile strength (UTS), elongation (EL.%) and yield strength (YS) of solder alloys were measured by tensile testing machine.

With the addition of Sb and Ce, the ß-Sn and intermetallic compounds of solders were refined and distributed more evenly. With the addition of Sb, the UTS, EL.% and YS of Sn-1.0Ag-0.5Cu increased by 15.3%, 46.8% and 16.5%, respectively. The EL.% of Sn-1.0Ag-0.5Cu increased by 56.5% due to Ce doping. When both Sb and Ce elements are added, the EL.% of Sn-1.0Ag-0.5Cu increased by 93.3%.

The addition of 0.5% Sb and 0.07% Ce can obtain better comprehensive performance, which provides a helpful reference for the development of Sn-Ag-Cu lead-free solder.

Based on the weak seismic performance and low ductility of coupled shear walls, engineered cementitious composites (ECC) is utilized to strengthen it to solve the deformation problem in tall buildings more effectively and study its mechanical properties more deeply.

The properties of reinforced concrete coupled shear wall (RCCSW) and reinforced ECC coupled shear wall (RECSW) have been studied by numerical simulation, which is in good agreement with the experimental results. The reliability of the finite element model is verified. On this basis, a detailed parameter study is carried out, including the strength and reinforcement ratio of longitudinal rebar, the placement height of ECC in the wall limb and the position of ECC connecting beams. The study indexes include failure mode and the skeleton curve.

The results suggest that the bearing capacity of RECSW is significantly affected by the ratio of longitudinal rebar. When the ratio of longitudinal rebar increases from 0.47% to 3.35%, the bearing capacity of RECSW increases from 250 kN to 303 kN, an increase of 21%. The strength of longitudinal rebar has little influence on the bearing capacity of RECSW. When the strength of the longitudinal rebar increases, the bearing capacity of RECSW increases little. The failure mode of RECSW can be improved by lowering the casting height of the ECC beam in a certain range.

In this paper, ECC is used to strengthen the coupled shear wall, and the accuracy of the finite element model is verified from the failure mode and skeleton curve. On this basis, the casting height of the ECC casting wall limb, the strength and reinforcement ratio of longitudinal rebar and the position of the ECC beam are studied in detail.

This paper aims to propose a novel blockchain crowdfunding projects evaluation approach using extended techniques for order preferences by similarity to ideal solution (TOPSIS) under fuzzy environment.

By analyzing the characteristics and operation process of blockchain crowdfunding model, this paper formulates the evaluation index system from three dimensions of human resources, capital and publicity. In addition, the entropy method is used to calculate the weight of each indicator to avoid subjective judgments; different alternatives are evaluated using the grey correlation analysis (GRA) and TOPSIS-integrated method which considers the distance and similarity between alternatives simultaneously.

By analyzing the characteristics and operation process of blockchain crowdfunding model, this paper formulates the evaluation index system from three dimensions of human resources, capital and publicity. In addition, the entropy method is used to calculate the weight of each indicator to avoid subjective judgments; different alternatives are evaluated using the GRA and TOPSIS-integrated method which considers the distance and similarity between alternatives simultaneously.

Blockchain crowdfunding has become a new model for fund-raisers to raise funds from public investors. This paper proposes a novel blockchain crowdfunding projects evaluation approach using extended TOPSIS under fuzzy environment.

The purpose of this paper is to provide the historical background of genealogical records and analyze the value of Chinese genealogical research through the study of names and genealogical resources.

The paper examines the historical evolution and value of Chinese genealogical records, with the focus on researching the Islamic Chinese names used by the people living in Guilin. The highlight of this paper includes the analysis and evolution of the Islamic Chinese names commonly adopted by the local people in Guilin. It concludes with the recommendations on emphasizing and making the best use of genealogical records to enhance the research value of Chinese overseas studies.

The paper covers the history of Islam and describes how the religion was introduced into China, as well as Muslims' ethnicity and identity. It also places focus on the importance of building a research collection in Asian history and Chinese genealogy.

This research study has a strong subject focus on Chinese genealogy, Asian history, and Islamic Chinese surnames. It is a narrow field that few researchers have delved into.

The results of this study will assist students, researchers, and the general public in tracing the origin of their surnames and developing their interest in the social and historical value of Chinese local history and genealogies.

The study of Chinese surnames is, by itself, a particular field for researching the social and political implications of contemporary Chinese society during the time the family members lived.

Very little research has been done in the area of Chinese local history and genealogy. The paper would be of value to researchers such as historians, sociologists, ethnologists and archaeologists, as well as students and anyone interested in researching a surname origin, its history and evolution.

This paper seeks to discuss the genealogical sources for Chinese immigrants as well as the settlement of Chinese in the USA and the historical evolution of Chinese names, their origins, arrangement and development. It aims to cover the origins of various classes of Chinese surnames, followed by the content description of a traditional genealogical book for jiapu.

The paper researches the various ways that a Chinese person can find out about their ancestry.

The paper reveals the roles of libraries, including serving the needs of patrons interested in genealogical research, preserving and interpreting information through oral and family history projects and collaborating with other libraries through interlibrary loan, document delivery, library consortia, collection management and international resource‐sharing.

The study provides information on where and how to locate the genealogical resources for researching the genealogy of a Chinese family.

The paper analyzes the value of genealogical research as a documentary source for population history, life expectancy in a clan, marriages and family connections, as well as lineage organizations and inter‐lineage relations.

This study aims to investigate the morphology and physicochemical properties of BiOBr/Polyvinylidene fluoride (PVDF) composite membranes and the differences in the properties of BiOBr/PVDF composite membranes made by adding different precursor ratios during the casting process.

In this paper, sodium bromide and Bi(NO3)3 were used as precursors for the preparation of BiOBr photocatalysts, and PVDF membranes were modified by using the phase conversion method in conjunction with the in situ deposition method to produce BiOBr/PVDF hydrophilic composite membranes with both membrane separation and photocatalytic capabilities.

The characterization results confirmed that the composites were successfully and homogeneously co-mingled in the PVDF membranes. The related performance of the composite membrane was tested, and it was found that the composite membrane with the optimal precursor incorporation ratio had good photocatalytic efficiency and antipollution ability; the removal efficiencies of methyl orange, rhodamine B and methylene blue were 80.43%, 85.02% and 86.94%, respectively, in 2.5 h. The photocatalytic efficiency of composite membranes with different precursor ratios increased and then decreased with the increase of the precursor addition ratio.

The composite membrane is prepared by phase conversion method with in situ deposition method, and the BiOBr material has unique advantages for the degradation of organic dyes. The comprehensive experimental data can be known that the composite membrane prepared in this paper has high degradation efficiency and good durability for organic dyes.

This study aimed to examine how Medical Expenditure Panel Survey (MEPS) data have been used to support scientific discoveries in biomedical and health sciences, and provide insight to researchers who are interested in using MEPS regarding collaborations and dissemination of research output.

A bibliometric approach was used to systematically examine the publications that used MEPS data and were indexed by PubMed and Web of Science (WoS). Microsoft Excel and bibliometric tools (WoS and VOSviewer) were utilized for quantitative and bibliometric network analysis. The measures were investigated on the total number of publications by year, research categories, source journals, other datasets/databases co-used with MEPS, funding sources, collaboration patterns, and research topics.

A total of 1,953 eligible publications were included in this study with the numbers growing significantly over time. MEPS data were primarily used in healthcare services, public environmental and occupational health research. The journals that published the most papers using MEPS were all in the healthcare research area. Twenty-four other databases were found to be used along with MEPS. Over 3,200 researchers from 1,074 institutions in 25 countries have contributed to the publications. Research funding was supported from federal, private, local, and international agencies. Three clusters of research topics were identified among 235 key terms extracted from titles and abstracts.

Our results illustrated the broad landscape of the research efforts that MEPS data have supported and substantiated the value of AHRQ's effort of providing MEPS to the public.

This paper aims to conduct two studies to investigate shared leadership and team creativity (TC) in leaderless short-term project teams (STPTs).

To answer the research question, this paper used a multi-level mixed-methods design. This paper analyzed video recordings, transcripts of STPTs’ collaboration and self-report surveys from an international engineering competition. In Study 1, this paper attempted to connect relation-oriented shared leadership (ROSL) and task-oriented shared leadership (TOSL) with TC by coding video recordings. In Study 2, this paper further investigated the proposed positive relationship between shared leadership and TC by surveying a sample of 166 students in 51 teams.

In Study 1, this paper found that shared leadership covaries with TC following a similar behavioral pattern. In Study 2, multi-level structural equation modeling results suggested that both TOSL and ROSL are positively correlated with TC.

In this mixed-methods multi-level research, this paper found that when the team’s shared leadership increases, their TC activity becomes frequent. This paper confirmed the qualitative finding by quantitatively investigated the relationship between shared leadership and creativity at the team level.